Similar design to truck manifolds but have extra material where needed to improve flow and increase strength, These manifolds fit most'54-'64 Y-block engines including 239, 272, 292 and 312 engines, Gaskets are included for a leak free installation, Exhaust ports are 1 3/8" x 1 3/8" but can be ported to 1 1/2", 2 bolt outlet flange for 2" pipe is included to connect the exhaust system. Tru-Ram® Cast Iron Ford Y-Block V8 Exhaust Manifolds. To help determine fit: "A" dimension, right angle to the exhaust port flange of the head, is 5.25. "B" dimension is in 2 measurements: from the centerline of the bolt holes UP; and from the centerline of the bolt holes DOWN. The UP dimension is 4.5", the DOWN dimension is 4".
Overall length from front-to-back is 18.5 One end bolt hole is slotted to the end of the casting. This will allow the installer to start one bolt into the engine to hold the gasket, and then slip the manifold onto that bolt and use that to support the manifold/gasket to make alignment and insertion of the other bolts much easier. The ports are just under 1.375 square. There is enough material around the ports to open them up to 1.5 or more, should the customer wish to do so. The 2-bolt flanges for beginning the head pipe installation are sized for 2 tubing.
They appear to be a fairly normal flange type, and could be opened up to 2.25 or more if the customer so desires. The outlet port of the manifold is bored to 2 ID.
The collector is centered between the center ports on the head. If you are reading this then you probably already know that Tru-Ram®s are the best cast iron manifolds for your Ford Y-Block engine. These Ford Y-Block exhaust manifolds are designed after the truck manifolds, but have extra material where needed to improve flow and increase strength. Does not included mounting hardware. Includes gaskets, steel exhaust hook-up flanges 2 I., and grade 5 hardware to hook up the 2 bolt collector flanges. Ford 272, 292, and 312 Y-Block. Note: These headers are not designed to support any accessory mounting such as alternator, power steering pumps, etc. These manifolds do not publicize a fit for any specific vehicle. Overall Length: 18.5 front-to-back. Port Dimensions: 1.375" x 1.375" can be opened up to approx. Exhaust Flange Outlet: 2 I. Can be opened up to approx.
Exhaust Flange Bolt Pattern: 2-bolt, 3-1/8 center-to-center. Please use the GIF chart below along with the following description. "A" dimension, right angle to the exhaust port flange of the head, is 5.25."B" dimension is in 2 measurements: from the centerline of the bolt holes UP = 4.5"; and from the centerline of the bolt holes DOWN = 4". Note: One end bolt hole is slotted to the end of the casting.
California Customers: This part has been identified as emissions sensitive and can only legally be installed on race-use only vehicles, off-road-use only vehicles, or pre-1965 vehicles in the State of California in accordance with the California Air Resource Board (CARB) requirements. Can't beat the look of ram horns. By Frosales on March 30, 2021. Love the look over the original crossover pipe.A true vintage dual exhaust! By Jim on January 10, 2021.
These reproduction ram horn manifolds are great. I have a friend with them on his Y block and sound good and looks great too. Yes, I recommend this product. By Mike on May 04, 2020.Are a great addition to my 1956 F100 project for my dad. By Dave on April 17, 2020. Using this product to give me extra room to mount a power steering pump.
Fits my 55 ford f100 with a 239 Y-block nicely. By The piddler on August 08, 2019. Beautiful castings with extra material for optional machining.Related Items / Suggested Parts. 1953-64 Ford F100 Truck 272/292/312 Y-Block Chassis Headers, Raw. Extreme Exhaust Header Gaskets, Ford Y-Block. Please take advantage of the add to cart button on each listing to get everything in your cart prior to completing checkout.
Speedway Motors is Americas Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 69 years. Repack the item in a sturdy box, include a copy of your invoice and complete the form on the back of the invoice. Speedway accepts full responsibility for the accuracy of our listings and product representation. The item "Tru-Ram Ford 54-64 Y-Block 239 272 292 312 V8 Retro Cast Iron Exhaust Manifolds" is in sale since Sunday, March 29, 2020. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Exhaust\Exhaust Manifolds & Headers".The seller is "speedway_motors" and is located in Lincoln, Nebraska. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.